Can I Install a Bathtub Myself? Factors to Consider And Actions
Can I Install a Bathtub Myself? Factors to Consider And Actions
Blog Article
What are your opinions on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging task. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified on your own for the task and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may require an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually already bought a new bathtub and also don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the tap as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally examine the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub ought to wait up until the bath tub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Installment
To start with, the sustaining structure supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall between the bath and the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are offered in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can break fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our article on How to Install a Bathtub Yourself. Many thanks for taking a few minutes to browse our article post. Enjoyed reading our write up? Please share it. Let somebody else find it. Many thanks for taking the time to read it.
Click
Report this page